prikaz prve stranice dokumenta Abrasion Wear Resistance of Precipitation-Hardened Al-Zn-Mg Alloy
  Preuzmi
PDF 11.48 MB
Znanstveni rad - Izvorni znanstveni rad
Abrasion Wear Resistance of Precipitation-Hardened Al-Zn-Mg Alloy
Materials, 17 (2024), 10; 1-14. https://doi.org/10.3390/ma17102446
Rodinger, Tomislav; Lukšić, Helena; Ćorić, Danko; Rede, Vera

Citirajte ovaj rad

Rodinger, T., Lukšić, H., Ćorić, D. i Rede, V. (2024). Abrasion Wear Resistance of Precipitation-Hardened Al-Zn-Mg Alloy. Materials, 17. (10), 1-14. doi: 10.3390/ma17102446

Rodinger, Tomislav, et al. "Abrasion Wear Resistance of Precipitation-Hardened Al-Zn-Mg Alloy." Materials, vol. 17, br. 10, 2024, str. 1-14. https://doi.org/10.3390/ma17102446

Rodinger, Tomislav, Helena Lukšić, Danko Ćorić i Vera Rede. "Abrasion Wear Resistance of Precipitation-Hardened Al-Zn-Mg Alloy." Materials 17, br. 10 (2024): 1-14. https://doi.org/10.3390/ma17102446

Rodinger, T., et al. (2024) 'Abrasion Wear Resistance of Precipitation-Hardened Al-Zn-Mg Alloy', Materials, 17(10), str. 1-14. doi: 10.3390/ma17102446

Rodinger T, Lukšić H, Ćorić D, Rede V. Abrasion Wear Resistance of Precipitation-Hardened Al-Zn-Mg Alloy. Materials [Internet]. 19.05.2024. [pristupljeno 15.06.2024.];17(10):1-14. doi: 10.3390/ma17102446

T. Rodinger, H. Lukšić, D. Ćorić i V. Rede, "Abrasion Wear Resistance of Precipitation-Hardened Al-Zn-Mg Alloy", Materials, vol. 17, br. 10, str. 1-14, Svibanj 2024. [Online]. Dostupno na: https://urn.nsk.hr/urn:nbn:hr:235:014979. [Citirano: 15.06.2024.]

Za citiranje koristite ovu mrežnu adresu: https://urn.nsk.hr/urn:nbn:hr:235:014979
Prijavite se u repozitorij kako biste mogli spremiti objekt u svoju listu.
Podaci o radu
Naslov (engleski)Abrasion Wear Resistance of Precipitation-Hardened Al-Zn-Mg Alloy
AutorTomislav Rodinger
AutorHelena Lukšić
AutorDanko Ćorić
AutorVera Rede
Autorova ustanovaSveučilište u Zagrebu
Fakultet strojarstva i brodogradnje
Znanstveno / umjetničko
područje, polje i grana		TEHNIČKE ZNANOSTI
Strojarstvo
Proizvodno strojarstvo
Sažetak (engleski)
The heat treatment of aluminum alloys is very important in industries where low weight in combination with high wear resistance, good strength, and hardness are important. However, depending on their chemical composition, aluminum alloys are subjected to different mechanical and thermal treatments to achieve the most favorable properties. In this study, an Al-Zn-Mg alloy was heat-treated including solution annealing at 490 °C for 1 h with subsequent artificial aging at 130, 160, and 190 °C for 1, 5, and 9 h. The hardness (HV1) and abrasive wear resistance with three different abrasive grain sizes were measured for all samples. The highest hardness was measured for the samples artificially aged at 130 °C/5 h, 227 HV1, while the lowest hardness was measured for the samples aged at 190 °C/9 h. The highest and the lowest wear resistance was also observed for the same state, i.e., artificially aged at 130 °C/5 h and 190 °C/9 h, respectively. The critical abrasive grain size was detected for some samples, where a decrease in wear rate was observed with an increase in the abrasive grain size from the medium value to the largest. The Response Surface Methodology (RSM) was applied to demonstrate the influence of the input parameters on the material wear rate.
Ključne riječi (engleski)
Jezikengleski
Vrsta publikacijeZnanstveni rad - Izvorni znanstveni rad
Status objaveObjavljen
Vrsta recenzijeRecenziran - međunarodna recenzija
Verzija publikacijeZavršna verzija rukopisa prihvaćena za objavljivanje (postprint)
Naslov časopisaMaterials
Brojčani podacivol. 17, br. 10, str. 1-14, 2446
e-ISSN1996-1944
DOIhttps://doi.org/10.3390/ma17102446
URN:NBNurn:nbn:hr:235:014979
Datum objave publikacije2024-05-19
URL dokumentahttps://www.mdpi.com/1996-1944/17/10/2446
Vrsta resursaTekst
Prava pristupaOtvoreni pristup
Uvjeti korištenjaIkona licence Imenovanje 4.0 međunarodna (CC BY 4.0)
Datum i vrijeme pohrane2024-05-22 10:55:38